The Mighty Cord RV Power Cord Adapter Plug # A10-5030DAVP referenced in your question features a 50-amp male to 30-amp female locking receptable. It has a voltage rating of 250V and can also be used with 120V.
This detachable RV adapter plug can be used for adapting 50-amp power for use with 30 amp trailers. I have attached a short video demonstration on this product that you can also check out. view full answer...
Yes, we do have a way to plug in a Redarc Brake Controller like item # RED24FR or item # RED44FR to the factory port on your motorhome's Freightliner XC Chassis. Since your motorhome's older you will need to use two separate connectors. The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers item # 3027-P and the Redarc Tow-Pro Wiring Adapter for Tekonsha Brake Controller Harness item # 331-TPH-017. These two harnesses combined will give you a plug and play installation. view full answer...
The Power Grip Generator Plug Adapter # CAM55333 referenced in your question is rated for 125 volts.
This adapter will allow you to connect your RV's 30-amp power plug to a 30-amp twist-lock receptacle on a generator. The twist-lock design on the adapter will also prevent the plug from disconnecting as the generator vibrates.
I have attached a short video demonstration on this product that you can check out. view full answer...
The Power Grip Generator Adapter for RV Power Cord # CAM55422 referenced in your question features an overall length, from end to end, of 14 inches.
This is a really nice 125-Volt adapter that will allow you to convert your RV's 50-amp power plug to work with a 30-amp twist-lock outlet on a generator. I have attached a short video demonstration on this product that you can also check out. view full answer...
The Rear View Safety Cigarette Lighter Adapter # RVS-505 measures 9-1/2" from the tip of the wires to the start of the 12v cigarette lighter, additionally this adapter also has an overall length of 13".
Attached is a diagram that shows these measurements as well. view full answer...
Yes, it does. The Hollywood Racks LED Light Bar item # HLY54RR is wired for a 4-way but comes with an adapter that will plug into a 7-way like yours to power the lights. view full answer...
I went out to the warehouse to measure Power Grip Replacement RV Power Cord Plug w/ Handle - 50 Amps - Male Item # CAM55255 as well as Power Grip Replacement RV Power Cord Adapter Receptacle w/ Handle - 50 Amps - Female Item # CAM55353.
Both measure 3-3/16 inches from the base of the plug to the end of the handle. I have included pictures showing this for you. view full answer...
The Hott Rod RV Water Heater Conversion Kit # DGR6VP includes 2 adapters that replace the Atwood Anode Rod/Drain Plug(1/2" NPT) # CAM11553 and Suburban Anode Rod(3/4" NPT) # CAM11563 for the electrical heating element. view full answer...
I went out to the warehouse and took a measurement of the SmartPlug RV Internet Inlet # SM38FR for you. I measured the total inside dimensions and the dimensions of the port.
The total inside height measurement is 2" and inside width is 1.5".
The Port height is .6" and the width is .5".
I have also included a diagram with these measurements to help visualize this. view full answer...
The Mighty Cord RV Power Cord Adapter # A10-3030D90VP is 12" long. We do have the Mighty Cord RV Power Cord # A10-3025ED90 which has the 30-amp twist lock and is 25' long. view full answer...
Since the Camco Adapter part # CAM55422 plugs into a 30 amp outlet and converts to a 50 amp socket it would put 15 amps on the two legs that normally carry 25 amps. view full answer...
The bottom mounting holes for the Jensen LED RV TV - 1080P - 1 HMDI - 12 Volts - 24" Screen # JEN46VR are approximately 5" from the bottom the of the tv. The mounting holes are spaced 3.94" apart side-to-side and top-to-bottom. I can't confirm that another brands 12v cable will have the correct connection for the tv but I can confirm that the Power Adapter Cord for Jensen LED Televisions - 12V DC # DCCIG09 will work with this tv to power it through a 12v "cigarette lighter" port. view full answer...
No, it won't but I have one that does. The Hopkins item # HM47570 is just an adapter that plugs into a round 7-way connector. To connect to your Ridgeline's factory 7-pin you will need the T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector item # 118288. This will replace your 4-way.
If you want to have both a 7-way and 4-way connector on your Ridgeline you'll want to install the Hopkins Endurance Multi-Tow Twist-Mount 7-Way RV and 4-Way Flat Trailer Connector item # HM40920... view full answer...
To replace your Dometic Duo-Therm 59561.501 AC unit, I recommend the Advent Air for Dometic Setups item # ACDOM150. This is a 15,000 Btu replacement option that plugs directly into your current Dometic setup and works seamlessly with your existing Dometic air distribution box and thermostat. The best part about the Advent Air is that has an adapter wiring kit, which saves you time and effort during installation.
This system does not have a heat option, but you can add the Electric Heat... view full answer...
You are correct. Now that you have LED's you will need two separate wiring harnesses for flat towing and trailer lights. Unless you want to run removable magnet lights like Item # RM-2120 from your RV over your Edge SEL you are going to want the Roadmaster Smart Diode 7-Wire to 6-Wire Wiring Kit item # RM38FR. This kit is the only one available for the 2017 Edge SEL and it includes everything you need to control your vehicles lights from your RV.
The best hitch for your Edge is going... view full answer...
In order to add a 7 way connector to your 2009 Suzuki Equator, you can simply use the # ETBC7, which will utilize your existing 4 way. You won't need to replace the existing harness, but once you plug it in to the ETBC7 you'll need to run a wire to your battery to supply 12v power and one to your brake controller to complete all of the circuits on the 7 way connector. I've linked a basic installation video of this connector that you can use as a guide.
When it comes to the towing capacity... view full answer...
The Draw-Tite Trailer Hitch, # 75101, is rated high enough (8,000 pounds GTW with WD). The limiting factor is how much your vehicle can tow. Check your owners manual to see what the towing capacity of your vehicle is and do not exceed it. I have included a link to the instructions for this hitch below.
When towing that much weight, I recommend using a brake controller if you do not already have one. One of our most popular models is the Tekonsha Prodigy P2 Brake Controller # 90885-3020-P.... view full answer...
Yes, we definitely do. Drilling into those LED's kills the entire light and we've heard some horror stories. The correct wiring kit for your 2019 Ford F-250 is the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit item # RM-15267. This kit includes everything you need for installation, including diodes that will work with your LED lights and act to prevent any type of electrical feedback. It also includes the 7-way to 6-way cable to connect your RV to your F-250.
Here are some other... view full answer...
Your 2018 Ram 1500 V8 Hemi tradesman should have an adapter to plug in the Tekonsha Plug-In Wiring Adapter item # 3024-P. The connector that the adapter plugs into is found up under the dash above the gas pedal. I have linked a picture of what it will look like below.
With the item # 3024-P you will be able to install the Tekonsha P3 Brake Controller item # 90195 to your Ram 1500 without cutting or splicing wires.
I have linked an installation video below. Right around the 1 minute mark... view full answer...
Go To Results